Skip to main content

You found it

The FSD Hardware Display.

The two generations of computer that run Tesla's Full Self-Driving, pulled out of the car and set up in my trunk so you can see them up close. Here's what you're looking at, and how it came together.

Computers
HW3 + HW4
On the bench
Live Tesla screen
Lives in
Model 3 trunk
HW3 and HW4 on clear acrylic, above the printed spec panel.

What you're looking at

Two computers, one screen, and the trunk they live in.

The short version: HW4 doubles the memory, takes in camera data at roughly four times the resolution, and is built for far larger AI models than HW3 was.

Full Self-Driving Computer

HW3/ AI3

Introduced in 2019. Tesla's first custom-designed silicon, built to process real-time vision from every camera on the car.

Introduced
2019
Memory
8 GB · 68 GB/s
Cameras
1.2 MP suite
Tesla FSD chips
2
Compute
144 TOPS

Full Self-Driving Computer

HW4/ AI4

Introduced in 2023. The next generation, engineered to handle vastly larger AI models and a big jump in camera data.

Introduced
2023
Memory
16 GB
Storage
256 GB NVMe
Cameras
5 MP sensors
Tesla FSD chips
2
Compute
Up to 5× AI3
A real Tesla screen, booted up and running in the trunk.

On the bench

The live Tesla screen.

That's a real Tesla touchscreen and computer, running on the bench in the trunk with no car around it. It's the same hardware that sits in the dashboard, booted up on its own right next to the computers that do the driving.

How it came together

Built by hand, and upgraded at almost every stop.

01The concept

It started as a Figma sketch.

I started on February 26, 2026, with one goal: show off Tesla's FSD hardware the way Tesla's own Service Centers do. Clean, labeled, and close enough to study. I pulled reference photos of those exhibits and laid out the proportions in Figma.

Then I handed the drawing to Gemini to render the finished piece sitting in the trunk, so I could see it before spending anything on materials.

Service Center references next to the first Figma layout.
Gemini's preview of the trunk, before anything was cut.
02The build

Measure, cut, test, repeat.

A cardboard mockup came first, to check sizes and angles without wasting real material. The slanted front piece was cut from 3/4-inch board on my school's bandsaw.

The base is fiberboard, roughed out on a borrowed bandsaw and trimmed at home on a table saw until it sat perfectly in the trunk.

Cutting the slanted front piece on the school bandsaw.
Trimming the fiberboard base until it sat flush.
The front piece, fresh off the saw.
First dry fit in the trunk. No wrap yet.
03The finish

Two crooked prints and a heat gun.

The front spec panel is adhesive-backed printed paper. The first print went on crooked. So did the second. With no time left before the first event, I spliced the cut pieces together by hand.

The base is wrapped in matte white car-wrap vinyl. It didn't love sticking to fiberboard, but a heat gun and a lot of squeegeeing got it to the clean finish I wanted.

Spec panel on, base still bare. Third attempt, spliced together by hand.
04The stands

Everything failed except CA glue.

The acrylic stands were cut on a bandsaw and finished with 2000-grit sandpaper. Joining the pieces was the hard part: epoxy clamped for 48 hours fell apart the moment the clamps came off, and several super glues did no better.

The CA glue I keep around for 3D-printed parts finally held, and held well.

First stand holding a board. Edges finished with 2000-grit paper.
Both stands, both boards. CA glue was the only thing that held.
05The upgrades

It hasn't stopped changing.

The first version was built for Chattanooga Charge. Since then it's had more upgrades than I can count, and the biggest one is the Tesla screen now running live on the bench in the trunk.

  1. Feb 2026

    First cut

    Figma sketch, cardboard mockup, first pieces of wood.

  2. Mar 2026

    Chattanooga Charge

    Debut in Chattanooga, Tennessee, with the boards on stage for the panel.

  3. Jun 2026

    Michigan Summer Meetup

    Heritage Landing in Muskegon, now with a Tesla screen running beside the boards.

  4. Oct 2026

    X Takeover

    Giga Texas in Austin, with the bench Tesla screen running in the trunk.

In the wild

Trunk open, all day.

Parked at the show so people can wander over between sessions and ask what actually changed from HW3 to HW4.

Tesla Owners Club of Michigan Summer Meetup, Muskegon.
Chattanooga Charge. The boards came up on stage for the panel.
Up close: the Tesla-designed chips everyone leans in to see.

Thanks for stopping by

Follow along for what goes in the trunk next.

I post teardowns, FSD drives, and every upgrade to this display on X. The full write-ups live here on the site.

Organizing a Tesla event? Get in touch.